| PLEX86 | ||
|
LONGslmodem and alsaHi, I'm using Slackware 10.1, kernel 2.6.7 on a DELL Inspiron 8600 with a winmodem, chipset Intel 82801DB ICH4, manufacturer Broadcom. I installed the packages of wvdial and wvstream from linuxpackages and I downloaded and compiled correctly the smartlink driver 2.9.9 wit alsa. The problem is the same of the others post (NO CARRIER), but (altough i read the posts) the solution doesn't work. The modules on the system are: Module Size Used by sndpcmoss 57256 0 sndmixeross 19200 1 sndpcmoss ipv6 227680 14 sndintel8x0 30344 1 sndac97codec 66564 2 sndintel8x0m,sndintel8x0 sndpcm 94344 3 sndintel8x0m,sndpcmoss,sndintel8x0 sndtimer 22532 1 sndpcm sndpagealloc 9736 3 sndintel8x0m,sndintel8x0,sndpcm sndmpu401uart 6656 1 sndintel8x0 sndrawmidi 21028 1 sndmpu401uart snd 52196 10 sndintel8x0m,sndpcmoss,sndmixeross,sndintel8x0,sndac97codec,sndpcm,sndtimer,sndmpu401uart,sndrawmidi yentasocket 18048 0 ohci1394 31236 0 Where did GRUB put my Windows bootloader On Sat, 05 Mar 2005 21:13:40 -0600, Mike Oliver staggered into the Black Sun and said: When you use fdisk to remove a parbreastion, that does not erase the data that's on... The sequence of command from the first terminal is: # slmodemd -d=1 -a -c=ITALY hw:0 SmartLink Soft Modem: version 2.9.9-alsa Mar 1 2005 02:08:03 02:08:03 modem `hw:0' created. TTY is `-dev-pts-5' Use `-dev-ttySL0' as modem device, Ctrl+C for termination. error: cannot set channels for playback: Invalid argument and from the second terminal: ATZ OK ATQ0 V1 E1 S0=0 &C1 &D2 +FCLbutt=0 OK ATDT411055 NO CARRIER ERROR .... The wvdial.conf is: Dialer Defaults Modem =dev-ttySL0 Baud = 460800 Init1 = ATZ Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLbutt=0 ISDN = 0 Modem Type = Analog Modem Phone = 411055 Username = *********** Pbuttword = *********** Carrier Check = no A weekend editorial: Slack vs. Mepis John Hasler It depends on how you define a distro. If you do it by how... I tryied also with: modprobe snd-intel-8x0m but it's the same. Also KPPP answer me with NO CARRIER. I tryed to put in myetc-modules.conf (that before of this was options snd cardslimit=2 alias snd-card-0 snd-intel8x0 alias snd-slot-0 snd-intel8x0 options snd-intel8x0m index=1 but the results are the same!!!! Somenone can help me??? -- Ciao da "Le battaglie si vincono con gli uomini che si hanno, non con quelli che si vorrebbero" (Napoleone Bonaparte) "Le cose che possiedi prima o poi ti possiedono..." (Fight Club) "Le donne possono avere bambini...gli uomini computers" (Anonimo) development process 3106 Perhaps. Or not. Refactoring, like a lot of other choices, are up to the individual developers, and get done as the developers, or their managers, notice problems justifying...
|
||||
Linux groups from Newsgroups The #1 Usenet Provider on the Internet
|
||||