USB not being buttigned IRQ on Toshiba Satallite

On a toshiba satalite laptop, live distros work fine, but SuSE 10.0 will only start after the install with acpi=off (similar experience with latest Mandrake). During the install the usb mouse works fine, but after the install usb is not working.

Any ideas as to how to get IRQs buttigned (dual booting with XP, so BIOS changes should be benign to that). Alternatively are there ways of 'tweaking ACPI'?

The relevant sections of dmesg to USB are:

PCI: PCI BIOS revision 2.10 entry at 0xe9964, last bus=2 PCI: Using configuration type 1 ACPI: Subsystem revision 20050408 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI: disabled PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 Boot video device is 0000:01:05.0 PCI: Transparent bridge - 0000:00:14.4 PCI: Using IRQ router default 1002-4353 at 0000:00:14.0 PCI: IRQ 0 for device 0000:00:13.0 doesn't match PIRQ mask - try pci=usepirqmask PCI: IRQ 0 for device 0000:00:13.1 doesn't match PIRQ mask - try pci=usepirqmask PCI: IRQ 0 for device 0000:00:13.2 doesn't match PIRQ mask - try pci=usepirqmask PCI: IRQ 0 for device 0000:00:14.1 doesn't match PIRQ mask - try pci=usepirqmask PCI: IRQ 0 for device 0000:02:06.0 doesn't match PIRQ mask - try pci=usepirqmask PCI: Bridge: 0000:00:01.0 IO window: c000-dfff MEM window: e0000000-efffffff PREFETCH window: a0000000-afffffff PCI: Bus 3, cardbus bridge: 0000:02:06.0 IO window: 0000b000-0000bfff IO window: 00001000-00001fff PREFETCH window: 90000000-91ffffff MEM window: d2000000-d3ffffff PCI: Bridge: 0000:00:14.4 IO window: a000-bfff MEM window: d0000000-dfffffff PREFETCH window: 90000000-9fffffff PCI: IRQ 0 for device 0000:02:06.0 doesn't match PIRQ mask - try pci=usepirqmask PCI: No IRQ known for interrupt pin A of device 0000:02:06.0. Please try using pci=biosirq.

then

shpchp: acpishpchprm:getdevice PCI ROOT HID fail=0x1001 ohcihcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) PCI: IRQ 0 for device 0000:00:13.0 doesn't match PIRQ mask - try pci=usepirqmask PCI: No IRQ known for interrupt pin A of device 0000:00:13.0. Please try using pci=biosirq. ohcihcd 0000:00:13.0: Found HC with no IRQ. Check BIOS-PCI 0000:00:13.0 setup! ohcihcd 0000:00:13.0: init 0000:00:13.0 fail, -19 PCI: IRQ 0 for device 0000:00:13.1 doesn't match PIRQ mask - try pci=usepirqmask PCI: No IRQ known for interrupt pin A of device 0000:00:13.1. Please try using pci=biosirq. ohcihcd 0000:00:13.1: Found HC with no IRQ. Check BIOS-PCI 0000:00:13.1 setup! ohcihcd 0000:00:13.1: init 0000:00:13.1 fail, -19

and

PCI: IRQ 0 for device 0000:00:13.2 doesn't match PIRQ mask - try pci=usepirqmask PCI: No IRQ known for interrupt pin A of device 0000:00:13.2. Please try using pci=biosirq. ehcihcd 0000:00:13.2: Found HC with no IRQ. Check BIOS-PCI 0000:00:13.2 setup! ehcihcd 0000:00:13.2: init 0000:00:13.2 fail, -19