no success in mounting digital camera as USB mbutt storage

Hello,

I have bought some exotic but cheap digital camera (VuPoint Solutions). Seems gtkam does not support it. So I try to mount it as an USB mbutt storage device. As far as I know I should just plug it in and then read `dmesg`, which would tell me what device should I mount.

When I plug it in and take a look at `dmesg`, I can see something like that:

(quotation starts) hub 1-0:1.0: state 5 ports 6 chg 0000 evt 0002 ehcihcd 0000:00:03.2: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb-s hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501 ehcihcd 0000:00:03.2: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT hub 1-0:1.0: portwaitreset: err = -107 hub 2-0:1.0: state 5 ports 3 chg 0000 evt 0002 ohcihcd 0000:00:03.0: GetStatus roothub.portstatus 0 = 0x00010101 CSC PPS CCS hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb-s hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 ohcihcd 0000:00:03.0: GetStatus roothub.portstatus 0 = 0x00100103 PRSC PPS PES CCS usb 2-1: new full speed USB device using ohcihcd and address 2 ohcihcd 0000:00:03.0: GetStatus roothub.portstatus 0 = 0x00100103 PRSC PPS PES CCS usb 2-1: default language 0x0409 usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: Product: COACH DSC usb 2-1: Manufacturer: ZORAN usb 2-1: SerialNumber: ZORAN00000001 usb 2-1: hotplug usb 2-1: adding 2-1:1.0 (config #1, interface 0) usb 2-1:1.0: hotplug hub 2-0:1.0: state 5 ports 3 chg 0000 evt 0002 SCSI subsystem initialized Initializing USB Mbutt Storage driver... usb-storage 2-1:1.0: usbprobeinterface usb-storage 2-1:1.0: usbprobeinterface - got id usb-storage: USB Mbutt Storage device detected usb-storage: -- buttociatedev usb-storage: Vendor: 0x0595, Product: 0x4343, Revision: 0x0000 usb-storage: Interface Subclbutt: 0x00, Protocol: 0x00 usb-storage: Transport: Control-Bulk-Interrupt usb-storage: Protocol: 8070i usb-storage: Endpoint sanity check failed! Rejecting dev. usb-storage: storageprobe() failed usb-storage: -- usbstorreleaseresources usb-storage: -- sending exit command to thread usb-storage: -- dissociatedev usb-storage: probe of 2-1:1.0 failed with error -5 usbcore: registered new driver usb-storage USB Mbutt Storage support registered. (quotation ends)

Seems there is some problem, but I don't understand a lot of this output. I can see there is no information about the device I should mount and there are problems reported, like: "Endpoint sanity check failed! Rejecting dev.", "storageprobe() failed" and "probe of 2-1:1.0 failed with error -5".

I would be very happy if somebody could help me to find out what happens, what goes wrong and what should I do to make it work right. Or just point me to some docs I should read or advice me some additional tests I should do...

Thanks a lot in advance!

--